Shipping class: Free Shipping
-
CMI California Swivel Version 2
Finally, a multi attachment non-pulley connections point for your suspensions bridge. The #CaliforniaSwivel offers you just the right amount of friction while giving you a wide surface area to be softer on your bridge than a rigging plate or conventional ring, all while keeping everything clutter free and in its place. Whether you run a…
-
CMI RESCUE 8 ALUMINUM DESCENDER
Big enough to handle the largest ropes–two of them. Extended horns on the upper ring make tying off a snap by preventing the rope from sliding up and locking off. Dual holes on the tie-in end allow the 8-Ring to remain attached to the harness while threading the rope, preventing loss of the device in…
-
CMI Rope Jack
The CMI Rope Jack is a Mechanical Advantage tool for pre-tensioning static lines, light lifting and cabling. The Rope Jack is small enough and light enough to be carried aloft by a climber for Mechanical Advantage within the crown. The length of the handle on the Rope Jack limits excessive loading to avoid rope damage.…
-
CMI RP105 Heavy Duty 5/8″ Rope Pulley
The RP105 from CMI is a pulley that is as serious as you are. Were talking 16,000 pound breaking strength with 5/8″ rope capability. The extra large rigging point accepts the largest carabiners–two of them. The extra wide, skirted sideplates fully enclose 5/8″ rope. MBS Rope Capacity Size Weight Efficiency 16000lbs 5/8″ 6.5×4.25in 1.35lb 92.1%
-
CMI RP107 Heavy Duty 5/8″ Rope Pulley
The largest of CMI’s heavy duty series. Stainless Steel sideplates, 4″ Aluminum sheave, Bushing, and Stainless Steel axle. MBS Rope Capacity Size Weight Efficiency 16000 lbs 5/8″ 7.5″ x 5″ 1.8 lb 93.7%
-
CMI Speed Line Kit
If you are in the market for an easy way to move cut limbs to the chipper then CMI’s speed line kit is the perfect option. The kit allows you to safely move limbs away from the base of the tree. CMI’s kit includes 10 aluminum D carabiners, 10 slings and one bale, which holds…
-
CMI STAINLESS STEEL PULLEY
A large capacity pulley based on our popular RP105 pulley, the RP149 utilizes a 2 ¾” diameter sheave with a 1″ rope capacity. This yields a larger rope capacity in a smaller pulley for special applications. Having the sideplates spaced apart at the top, helps reduce the pulley moving on the carabiner. Stainless steel axle,…
-
CMI STAINLESS STEEL ROPEWALKER ASCENDER
Designed to accommodate left and right handed users, the Ropewalkers grabbing pressure is maintained by the beefiest spring wire in CMI’s lineup. Slots in the bottom are designed to pass chips, grit, and mud right on through. For ropes 7/16 – 5/8 inches.
-
CMI VELOCITY MICRO TROLLEY PULLEY
The CMI Velocity Micro Trolley is a smaller version of the Heavy Duty Trolleys that CMI Makes. This trolley will work on up to 1/2″ rope and cable. It features 1.5″ Stainless Steel Sheaves that are on ball bearing and a Stainless Steel axle. Made in the USA. The trolley is easily removed from the…
-
CMI XL ALUMINUM SHEMBINER HOOK
X-Large Shembiner Hook by CMI®. The New Shembiner XL is a lightweight aluminum hook that attaches to your harness which is wide enough for your chainsaw handle to fit inside the hook itself. That allows the climber to quickly and easily remove and rack chainsaws and tools without having to fiddle around with a gate.…
-
RNA COLLAPSIBLE THROWLINE CUBE
Collapsible – The RNA Throwline Folding Cube folds into a small triangle for easy carrying to the job site. Secure tightly with velcro strap to keep everything secure. Durable – Constructed with heavy duty canvas material for long lasting use. It is light weight and easy to carry. Helps throw line remain tangle free and…
-
CMI MICRO SINGLE PULLEY
[et_pb_section bb_built=”1″][et_pb_row][et_pb_column type=”4_4″][et_pb_text] The RNR/CMI RP110 micro pulley is used primarily used as a slack tender for your friction hitch. The sideplates swing open to allow placement anywhere on the line. The aluminum cheeks have 7/8″ hole for a carabiner. A double lock nut hold everything together on an aluminum axle. Made in the U.S.A.…
-
Edelrid TREE CRUISER
The TREE CRUISER system complements our foot ascender FOOT CRUISER with a connecting plate. This way it is possible to attach it to the TALON climbers. PRODUCT INFORMATION Cam with self-cleaning slots for optimum grip on frozen or muddy ropes Pre-installed but removable rope safety device to prevent unintentional release Ascent loop fitted with abrasion…
-
FOX40 Classic Whistles
Heavy duty, no freeze, pea-less super loud whistle for signaling and communications. Useful tool for search and rescue and your survival kit. Put one on your P.F.D!!! Made in Canada.
-
GIBBS Free Running Ascender
Gibbs Ascenders are designed not to slip on muddy or icy ropes.
-
GIBBS 1/2 in Aluminum Shell w/Forged Cam
Designed for litter raising and load hauling
-
GIBBS 1/2 in Stainless Steel Shell Ascender
Designed for scenarios involving live loads
-
GIBBS KLIMAIR BI-DIRECTIONAL ASCENDER
The Gibbs Klimair swiveling ascender is primarily used for 2-in-1 work positioning lanyards. It may also be useful in specific ascending and rigging applications. A simple but secure pin assembly system means you can quickly attach the system to a 1/2″ rope. The bi-directional mechanical prusik has a swiveling stainless steel eye and an aluminum…
-
GIBBS Spring Kit
Gibbs Spring Kit replaces old style coil spring with a cable spring. We also have a spring replacement kit available for the ½” (13mm) ascenders. If you are handy with a drill and a few hand tools you can replace the spring and cover with a cable spring. Made in the U.S.A. There is no spring replacement…
-
GIBBS Spring Loaded 1/2 in Aluminum Ascender
Gibbs Spring Loaded, Aluminum Shell model – not designed for bearing the weight of more than one person.
-
Hand Held Hot Knife
Cuts and seals synthetic rope in seconds. The best way to prevent nylon rope from fraying is to melt the ends, but everyone who has done it knows it’s a slow, messy, smelly operation that often results in flaming drips and burnt fingers. Instead use this handheld heat gun – it cuts and seals the ends…
-
ISC Compact Rigging Pulley- for 1/2 in Rope
At approximately half the size of the standard small rigging pulley and weighing in at only 490g (1lb), the new Compact Rigging Pulley offers a highly impressive strength to weight ratio with an MBS of 19,000 lbf. (85 kN) and a WLL of 3,800 lbf. (17kN). The Pulley plates are made from hot forged Aluminium…
-
ISC Large Cast Pulley- for 19 mm (3/4 in) Rope
ISC Rigging Blocks have color-coded Side Cheeks and Pulley Wheels, helping the user to easily identify the correct Block for the task. We have introduced a new fixed bollard dimension, which allows the user to fall in-line with rigging standard practice, whereby the Anchor/Topping Strop should be twice the Strength of the Working Line.
-
ISC Rope Wrench
The Zk-2 Singing Tree Rope Wrench (STRW) is manufactured and distributed worldwide by ISC. The STRW enables Single Rope Technique (SRT) climbing, minimises slack in the system, ensures consistent friction, allows 1 : 1 efficiency, allows simple re-directs and can easily be set up on multiple limbs. The Zk-2 model has rounded side plates…
-
ISC STRYDER RIGHT FOOT ASCENDER
ISC Wales is a well-respected name in any industry that requires climbing. The Stryder Foot Ascender is created with the arborist specifically in mind and includes a lightweight cam with a coned face for firm and reliable grip with minimal wear on your rope. The foot-operable cam lever can be removed, and the webbing straps…
-
KASK Bayonet Ear Muff adapter for Plasma and Super Plasma Helmets
The Kask Bayonet Adapter Set for Ear Muffs is installed directly onto the Plasma, Super Plasma, or HD helmets so that Kask Ear Defenders can be attached. This adapter set is required for installing Kask SC1, SC2, and SC3 Ear Defenders.
-
kask ear defenders sc1 green
The green SC1 earmuffs are used in general industrial work areas. Suitable for situations with a low to medium noise level (dB) and with medium to high frequency. Attachment to the helmet with a bayonet adapter Universal 30 mm euro slot Performance differentiated by color Smooth telescopic size regulation Non-conductive Certified for use with KASK…
-
KASK EAR DEFENDERS SC2 yellow
The yellow SC2 earmuffs are suitable for environments with a medium to high level of noise (dB). The best choice in high frequency noise situations. Suitable for a wide variety of uses such as: building and construction, forestry use, industrial areas, production areas, agriculture, etc. Attachment to the helmet with a bayonet adapter Universal 30…
-
KASK SUPER PLASMA
The Kask Super Plasma HD Safety Helmet has maximum ventilation thanks to ten air intakes. The helmet is equipped with lamp clips and a visor attachment. These universal helmets are adjustable from 20 to 24 3/8 in (51 – 62 cm) and have an inner shell made of HD Polystyrene for ultimate protection and comfort.…
-
KASK SUPER PLASMA HI VIZ
The Kask Super Plasma HI VIZ Helmet has maximum ventilation thanks to ten air intakes. The helmet is equipped with lamp clips and a visor attachment. These universal helmets are adjustable from 20 to 24 3/8 in (51 – 62 cm) and have an inner shell made of HD Polystyrene for ultimate protection and comfort.…
-
kask V2 Plus Visor
Anti-fog and scratch resistant treatment Panoramic lens compatible for overlapping corrective glasses Cut proof edge Drip proof upper contour made of rubber Impact resistant even at extreme temperatures
-
KASK VISOR ADAPTER SET FOR ZENITH VISORS
Kask visor adapter set for zenith visors.